Products + Services

How to tell if your apartment has mold—and how to get rid of it

  • Three common causes are leaks from another apartment, a clogged HVAC unit, and broken washing machine hose
  • Warning signs include musty odors, dark spots and water stains on walls, and headaches or other health problems
  • Treatment typically involves a full-scale mold remediation by a licensed pro—which may be covered by insurance
Mimi headsht
By Mimi OConnor  |
September 7, 2023 - 12:30PM
insurance adjuster inspecting mold

You might notice water damage and staining before you notice any signs of mold, because mold tends to grow faster inside the wall than on the surface. 

iStock

It doesn’t matter where you live in New York City—whether it's a small, prewar building or a modern luxury tower—you may still have to deal with the problem of mold.

In fact, Jeffrey Gross, a water damage and mold remediator at First Onsite (formerly Maxons Restorations), says that his company sees newer buildings with mold problems more often than older ones.

"We respond to plenty of leaks in old and new buildings, but I think we do more mold remediation in newer buildings," he says. That's because materials used in newer buildings don't breathe as much, and if there is some kind of leak or water damage, mold can grow. Older buildings tend to have fewer materials that mold can grow on, whereas engineered flooring, sheetrock, and processed materials are "junk food for mold," he says.


[Editor's note: An earlier version of this post was published in August 2022. We are presenting it again with updated information for September 2023.]


What are the three common causes of mold—and what should you do about them?

Moisture encourages mold growth—so places like bathrooms and basements are top spots for mold growth, as are areas around heating and cooling appliances and vent ducts.

According to Gross, the following three scenarios are the most common ways mold takes hold in NYC apartments, both new and old.

Cause #1: A leak from another apartment

Broken pipes and water overflows can soak your ceiling and walls from above, or seep into your floors and walls from the side. The most common offender: Plastic water supply lines to sinks and toilets, which newer buildings tend to use. (Tip: Copper, found in older buildings, almost never leaks, Gross says. Galvanized steel is another sturdy material.)

Treatment: If, for example, your upstairs neighbor's toilet or shower overflows into one room of your apartment, your ceiling and walls would be affected. Professional water remediation—which involves drying out the area behind the wall to prevent mold—starts at around $1,200. This process takes three to 10 days and includes sucking up the standing water and making holes in the wall to ventilate the wall cavities. It might also involve taking down a light fixture to get air into the ceiling, cleaning and treating all surfaces with an antimicrobial agent, and setting up drying equipment.

If mold is present and the affected area exceeds 10 square feet, NYC Health Department guidelines require a full-scale mold remediation by a trained and qualified professional like Gross. New York State requires mold remediation companies to be licensed. The law also makes it illegal for companies to do both mold testing and remediation, as there’s an inherent conflict of interest.


Expect the fee to run $8,000-$15,000 for a full mold remediation. It's not cheap, but your renter’s or homeowner’s insurance may cover the cost, with insurers paying for clean-up and drying and steps to retard mold growth. As with any insurance policy, there are limits to what is covered.

The mold exclusions usually come into play if the mold issue blows up months later or comes from a source that is not related to a covered peril—a blocked bathroom vent, for example, or from general damp conditions.

But if it was your tub or toilet that overflowed, that would generally be covered under the liability portion of your policy up to the property limits for mold in your own residence or the liability limit if the mold is in another apartment.

(For more information on insurance coverage for mold claims, check out our guide here.)

Cause #2: Clogged HVAC units 


All-in-one heating-and-cooling units, lodged radiator-style against the wall, are a huge blind spot for NYC apartment owners in newer buildings, who tend to forget that HVAC units require twice-yearly maintenance, and that falls under the apartment owner’s responsibility, Gross says. If you rent, it’s your landlord’s responsibility. 

There are two kinds of units: PTAC and fan-coil. "The difference is the fan-coil gets its heat and cooling from a central plant, while the PTAC produces it at the unit," he explains, adding that both have coils, filters, and condensate pans, so the issue is the same regardless of which one you have.

According to Gross, the most common problem with HVAC units is that the filter is not replaced often enough. Dust collects and clogs the drain of the condensate pan, which then overflows and leaks under the floor. Neglecting to change filters after a renovation that generates a lot of dust can also clog the drain to the pan.

Gross says these scenarios tend to cause mold more often than other types of leaks because they leak so slowly into the floor that it goes undiscovered until a large section of flooring shows damage. Nearby sheetrock can also be impacted, as it wicks up the moisture from the floor.

Treatment: If you are lucky enough to catch the leak soon after it begins and mold isn’t present, cleanup may just involve removing a few floor tiles and the base molding and drilling a hole to dry the wall cavity. This can run from $800 to $1,500 and require minimal repairs.

These situations always require a full-scale mold remediation, which typically involves ripping out a few square feet of floor, sheetrock, and base molding to get rid of the mold.

The average cost is around $6,000, plus the cost for a contractor to come in and repair the area afterward.

Cause #3: A broken washing machine hose 

"We get a lot of these," Gross says, placing the blame on cheap rubber washing machine hoses. “Those are the ones that break, as opposed to the under $30 stainless-steel-wrapped hoses you can buy at Home Depot that almost never leak."

Treatment: For minor damage, the removal of moldings and drilling of holes to promote air circulation and drying, for a cost from $1,200 to $5,000.

If mold has already set in, a full-scale remediation would entail removing the flooring and base moldings, cutting the sheetrock walls up two feet around the perimeter of the room, and then treating the area as described below.

The price is typically $8,000-$12,000.

What's the difference between mold and mildew?

Neither is pleasant, but mold is likely to cause you a lot more grief than mildew.

Both are also fungi, but mildew—usually a gray or white color that can become black as the fungus grows—is a surface fungi. This is an important distinction because that means some elbow grease and household cleaner can usually contain a mildew situation.

Mold, however—which tends to be fuzzy and come in several shades (black, white, green, and yellow)—is embedded in the material. This is why getting rid of any significant mold infestation requires the physical removal of infected areas, like sections of walls and flooring.

And that's one reason why it’s so costly to remediate mold. Another is all the precautions that must be taken to prevent cross-contamination, including sealing off and ventilating the area, doing a thorough cleaning, and careful disposal.

"It’s more of a surgical removal than a demolition,” Gross says. “We don’t use sledgehammers—we use knives and spray bottles to wet down the material. The debris we create is bagged in [plastic] bags taped shut, and the exterior has to be vacuumed to prevent cross-contamination. Surfaces that can’t be removed, like a concrete slab, have to be cleaned and if there is evidence of contamination, have to be encapsulated in an antimicrobial sealant, like a primer."

Beware of remediation companies that offer "mold fogging," or filling wall cavities with spray foam, rather than full removal of the contaminants.

How to tell whether you have mold 

It’s not always obvious that mold is present, so be on the lookout for these tell-tale signs:

Water damage: You'll probably notice water damage and staining before you notice any signs of mold, because mold tends to grow faster inside the wall than on the surface. That’s why it’s important to address any moisture problems quickly.

Odor: One of the first signs that mold might be present is a wet, musty smell or the smell of moldy, wet building materials. These indicate a moisture problem that can lead to mold; it doesn't necessarily mean you have mold.

Spots: Black, gray, green, or brown spotting. Only proper testing can prove whether or not it’s mold, but if you see spotting on a surface like sheetrock that is or was wet, it’s worth testing, Gross says.

Health problems: Respiratory reactions including asthma are most common, though mold sensitivity can also cause headaches, irritated eyes, and skin rashes. Some people have symptoms immediately; for others, it develops over time. Note that not all types of mold cause health problems, and not all black mold is “toxic mold.” To identify which type of mold you have, an industrial hygienist will need to collect a sample for testing.

If you suspect you have mold, there are many at-home mold testing kits available. (You may have to pay an additional fee for lab processing.) You can also hire a certified industrial hygienist to take air samples, perform a survey, and devise a clean-up plan.

Who should pay for getting rid of mold? 

It depends. If you bought in a newer building that has mold, you may be able to sue the developer in certain circumstances, such as when leaks and mold are the result of design defects and exist throughout the building. Those kinds of cases can be expensive, so you might want to lean on the board to bring the lawsuit, though one real estate attorney reported successfully securing a multi-million dollar settlement for an individual client in a mold-related case.

If you're renting, you shouldn't have to pay to remediate mold, experts say. Learn more about filing a mold complaint with the city.

A cost-effective way of forcing repair or remediation would be through housing court. These lawsuits are available to renters (and owners) in co-ops or condos, whereby a rent abatement may be available under the warranty of habitability.

Whether you are an owner or renter, you'll want to engage the services of an experienced attorney to handle the case. 

 

Mimi headsht

Mimi OConnor

Contributing Writer

Mimi O’Connor has written about New York City real estate for publications that include Brick Underground, Refinery29, and Thrillist. She is the recipient of two awards from the National Association of Real Estate Editors for interior design and service journalism. Her writing on New York City, parenting, events, and culture has also appeared in Parents, Red Tricycle, BizBash, and Time Out New York.

Brick Underground articles occasionally include the expertise of, or information about, advertising partners when relevant to the story. We will never promote an advertiser's product without making the relationship clear to our readers.

topics: